Hydraulic Vane Pump Manufacturer

Hydraulic Vane Pump Manufacturers Vane Pumps

A hydraulic vane pump is a positive-displacement pump that consists of vanes mounted to a rotor that rotates inside of a cavity. In some cases these vanes can be variable length and/or tensioned to maintain contact with the walls as the pump rotates.

Read More

Hydraulic Vane Pumps | Hydraulic Vane Pump Manufacturers | Vane Pumps Manufacturer

Hydraulic Vane Pumps

While vane pumps can handle moderate viscosity liquids, they excel at handling low viscosity liquids such as LP gas (propane), ammonia, solvents, alcohol, fuel oils, gasoline, and refrigerants. Vane pumps have no internal metal-to-metal contact and self-compensate for wear, enabling them to maintain peak performance on these non-lubricating liquids. Though efficiency drops quickly, they can be used up to 500 cPs / 2,300 SSU.

hydraulic vane pumps hydraulic vane pump hydraulic vane pump

Vane pumps are available in a number of vane configurations including sliding vane, flexible vane, swinging vane, rolling vane, and external vane. Vane pumps are noted for their dry priming, ease of maintenance, and good suction characteristics over the life of the pump. Moreover, vanes can usually handle fluid temperatures from -32°C / -25°F to 260°C / 500°F and differential pressures to 15 BAR / 200 PSI (higher for hydraulic vane pumps).

Each type of vane pump offers unique advantages. For example, external vane pumps can handle large solids. Flexible vane pumps, on the other hand, can only handle small solids but create good vacuum. Sliding vane pumps can run dry for short periods of time and handle small amounts of vapor.

How Hydraulic Vane Pumps Work

Despite the different configurations, most vane pumps operate under the same general principle described below.

1. A slotted rotor is eccentrically supported in a cycloidal cam. The rotor is located close to the wall of the cam so a crescent-shaped cavity is formed. The rotor is sealed into the cam by two sideplates. Vanes or blades fit within the slots of the impeller. As the rotor rotates and fluid enters the pump, centrifugal force, hydraulic pressure, and/or pushrods push the vanes to the walls of the housing. The tight seal among the vanes, rotor, cam, and sideplate is the key to the good suction characteristics common to the vane pumping principle.

2. The housing and cam force fluid into the pumping chamber through holes in the cam . Fluid enters the pockets created by the vanes, rotor, cam, and sideplate.

3. As the rotor continues around, the vanes sweep the fluid to the opposite side of the crescent where it is squeezed through discharge holes of the cam as the vane approaches the point of the crescent . Fluid then exits the discharge port.

hydraulic vane pump hydraulic vane pump hydraulic vane pump

Advantages

Handles thin liquids at relatively higher pressures
Compensates for wear through vane extension
Sometimes preferred for solvents, LPG
Can run dry for short periods
Can have one seal or stuffing box
Develops good vacuum
Disadvantages
Can have two stuffing boxes
Complex housing and many parts
Not suitable for high pressures
Not suitable for high viscosity
Not good with abrasives

Applications

Aerosol and Propellants
Aviation Service - Fuel Transfer, Deicing
Auto Industry - Fuels, Lubes, Refrigeration Coolants
Bulk Transfer of LPG and NH3
LPG Cylinder Filling
Alcohols
Refrigeration - Freons, Ammonia
Solvents
Aqueous solutions

Materials Of Construction / Configuration Options

Externals (head, casing) - Cast iron, ductile iron, steel, and stainless steel.
Vane, Pushrods - Carbon graphite, PEEK
End Plates - Carbon graphite
Shaft Seal - Component mechanical seals, industry-standard cartridge mechanical seals, and magnetically-driven pumps.
Packing - Available from some vendors, but not usually recommended for thin liquid service

 

Links

  •      

WHY US?

  • Stringent checks of quality
  • Services after sale
  • Quantitative & Qualitative range
  • Well equipped and modern manufacturing unit
  • Technically sound professionals

CONTACTS

  • Mr. Rama Raju Namburi  (CEO)
    Plot No. D - 62 / A, Phase - 5, I. D. A., Jeedimetla,Hyderabad, Andhra Pradesh - 500 055, India
    Email :

    koojanhydraulics@yahoo.com
    info@koojanhydraulics.com

    Telephone : +91-40-40206315
    Mobile :
    +(91)-9848203038
    Fax : +91-40-40206315